ادب میں دلچسپی
ناطق کو بچپن ہی سے ادب میں گہری دلچسپی تھی بتاتے ہیں کہ وہ میٹرک تک نصاب کی کتا بیں نہیں پڑھا کرتے تھے بلکہ دوسری کتابو ں کو پڑھنے اور گھر کے پاس سکول کی لائبریری جانے میں زیادہ دلچسپی تھی اور بقول ان کے انھوں نے بچپن میں ہی ایسی کتا بیں پڑھ رکھی تھیں جن میں کسی کوکم ہی گہری دلچسپی ہو سکتی ہے مثلاً ’’داستان امیر حمزہ‘‘’’الف لیلا‘‘ یہ کتابیں وہ بچپن میں ہی پڑھ چکے تھے اور ان میں سے بہت سے صفحات ان کو زبانی یاد بھی تھے ایک دلچسپ واقعہ جس کاذکر کرتے ہوئے وہ کہتے ہیں :
’’آب حیات کتاب جب میں نے پڑھی تو وہ مجھے ایسے ماحول اور کلچر میں لے گئی کہ وہ کتاب میں نے تقریباًچالیس دفعہ پڑھی ہوگی جب بھی پڑھتا ہوں تو ایک نیا لطف آتا ہے۔میں نے سوچا کہ شاعر ایسے ہوتے ہیں یہ تو بہت اچھے لوگ ہیں اور ان کی حرکتیں بھی مجھے راس آئیں اس میں جتنے شاعر تھے میرے لیے خاص طور پر ان دنوں وہاں مجھے انشاء جی بہت بھائے جس طرح مولوی آزاد صاحب نے مصحفی ساتھ ان کی مبالغہ آرائی کروائی ہے۔بچپن میں ایک بندے کو ہیرو کی طرح سمجھ لیا جاتا ہے میرے لیے مصحفی ان دنوں ولن تھا مولوی آزاد نے ان کو ولن بنا کررکھ دیا تھا۔اب ہوش آیا توپتا چلا مولوی آزاد کیسے کھیل کھیلتے تھے۔(2)
کتابوں سے دلچسپی ان کی نہ صرف ادب سے راہیں ہموار کرتی گئی بلکہ ادبی دنیا میں ممتاز لکھاری کے طور پر پہچان کا باعث بنی۔
Tujuan dari penelitian ini untuk mengembangkan sebuah sistem informasi persediaan gudang berbasis website dengan menggunakan metode waterfall. Tahapan model pengembangan sistem yang dilakukan mulai dari analisa, desain, code generation, testing dan support. Teknik pengumpulan data yang diterapkan dalam penelitian yaitu: observasi, wawancara, dan studi pustaka. Ruang lingkup subjek penelitian tentang sistem persediaan gudang yaitu pada toko sugi teknik. Di mana ruang lingkup meliputi merancang sistem persediaan gudang untuk mengelola stok barang, proses pencatatan, proses pendataan pasokan barang di toko sugi teknik hingga pembuatan laporan barang keluar dan masuk, proses laporan data transaksi dari supplier dan konsumen. Sistem informasi ini berisi pencatatan barang masuk dan keluar, laporan penjualan, laporan pembelian, laporan retur atau operasional dan serta laporan pendapatan laba sehingga memudahkan mendapatkan informasi dengan cepat, jelas dan akurat.
The role of process parameters; time, temperature and applied pressure, in fabricating ceramic-ceramic joints with a metallic interlayer through pressure assisted air brazing in a purpose built furnace has been studied. The focus has been mainly on the alumina-alumina bonds prepared with pure aluminum interlayer. However some samples were also prepared with various aluminum-silicon alloys, pure copper and nickel plated copper interlayer. To broaden the application of the developed technique, samples prepared with nickel plated copper interlayer were also studied in some detail. The furnace was designed and fabricated in such a way that it was possible to apply an accurate load upto 30 MPa with the help of a lever mechanism. The temperature range employed during experimentation was 700-1150oC, while the holding time was varied from 15 to 240 minutes. The joints were tested for their flexural strength through four point bend test. Asjoined samples were studied through optical and scanning electron microscopy for integrity of the interface as well as changes in thickness of the interlayer. The selected fractured samples were studied through scanning electron microscopy to correlate the improvement in the strength with the changes in interface. It was observed that the application of the pressure during the brazing process greatly reduced the holding time as well as the processing temperature for a given joint strength. It was further observed that in the joints prepared under applied loads, it was possible to obtain joint strength which was many times higher than the maximum obtainable in samples prepared under comparable holding time, temperature and atmospheric conditions but with no applied load.