Journey to Khalafah and Tamkeen fil ‘Ard Milestones on the Way

Establishment of khilafah and tamkeen fil ‘ard means supremacy of the dictates of shari‘ah and socio-political justice on earth. This is one of the basic objectives and prominent messages of the Holy Quran and Seerah of Prophet Muhammad (s.a.w). About khilafah and tamkeen fil ‘ard the Holy Quran expresses as:   -وَعَدَ اللَّهُ الَّذِينَ آمَنُوا مِنكُمْ وَعَمِلُوا الصَّالِحَاتِ لَيَسْتَخْلِفَنَّهُم فِي الأَرْضِ …  -الَّذِينَ إِن مَّكَّنَّاهُمْ فِي الأَرْضِ أَقَامُوا الصَّلاَةَ وَآتَوُا الزَّكَاةَ وَأَمَرُوا بِالمَعْرُوفِ وَنَهَوْا عَنِ المُنكَرِ وَلِلَّهِ عَاقِبَةُ الأُمُورِ.  -هُوَ الَّذِي أَرْسَلَ رَسُولَهُ بِالْهُدَى وَدِينِ الْحَقِّ لِيُظْهِرَهُ عَلَى الدِّينِ كُلِّهِ وَكَفَى بِاللَّهِ شَهِيداً.  Prophet Muhammad (s.a.w) proclaims:   - وَاَللَّهِ لَوْ وَضَعُوا الشَّمْسَ فِي يَمِينِي وَالْقَمَرَ فِي يَسَارِي عَلَى أَنْ أَتْرُكَ هَذَا الْأَمْرَ حَتَّى يُظْهِرَهُ اللَّهُ أَوْ أَهْلِكَ فِيهِ مَا تَرَكْتُهُ. The Holy Quran and the Seerah refer to some underlying milestones on the way of religious nations to status of khalafah and tamkeen fin ‘ard. These milestones may be expressed in an order as: da‘wah [preaching], deen [practices of prophetic teachings], hijrah [migration], ma‘iyyat-ul-Allah [companionship of Allah], qital [wars], nusrat-ul-Allah [divine aid], izhar-ud-deen [domination of deen] and khilafah [inheritance of authority]. This is noteworthy that journey of khalafah and tamkeen fin ‘ard begins with da‘wah [preaching towards deen] and passing through various milestones ends up again at da‘wah, as obvious from ayat-ul-istakhlaf quoted above. Therefore, the seekers of khilafah and tamkeen fil ‘ard should strive hard and keep struggling with the work of da‘wah with dedication in all circumstances and all means as per time and place requirements in lined with the modus operandi of Prophets, particularly Prophet Muhammad (s.a.w), instead of awaiting the status of khilafah and tamkeen fil ‘ard as prerequisite to start with the work of da‘wah and establishment of deen. This paper primarily aims to elaborate the milestones of Muslim Ummah to reach to the status of khilafah and tamkeen fil ‘ard. It also cast light on the objectives of khilafah and tamkeen fil ‘ard. This work provides useful guidance to Muslim Ummah in general and Ahlud da‘wah in particular about milestones and objectives of khilafah and tamkeen fil ‘ard.

Effect of Samarium Additions on Shape Memory and Thermomechanical Behavior of Iron Based Shape Memory Alloys

In the present work, a comparative study of the shape memory and thermomechanical behavior of four alloys containing different amount of samarium have been carried out at a strain rate of 0.08x10 -6 s -1 . After hot rolling, annealing and solution treatment, the alloy samples were tensile deformed at room temperature from 1% to 5% and were then recovered at 600̊C for 20 minutes repeatedly for six times to complete six training cycles. It has been found that the addition of samarium strengthens the austenitic matrix, increases the c/a ratio and reduces the grain size. It has been noticed that the addition of samarium (0.64 wt. %) improves the shape memory effect when the alloys were strained from 1% to 5%. This improvement in shape memory effect presumably can be regarded as the increase in strength, increase in c/a ratio and absence of ά (martensite). It has been further noticed that when samarium contents are gradually reduced from 0.64 % to 0.21% the shape memory effect decreases. The decrease in shape memory effect by the decrease in samarium contents can be attributed to decrease in strength, decrease in c/a ratio and formation of ά (martensite). It has been further noticed that the shape memory effect decreases with the increase in amount of strain. It is found that thermomechanical treatment (training) results in improvement of shape memory effect and has a significant influence on mechanical parameters like proof stress (σ 0.002 ), critical stress (σ 0.0008 ) and strain hardening exponent. The improvement in shape memory effect by thermomechanical treatment can be regarded as the effect of reduction in the values of proof stress and critical stress during training which facilitates the formation of ε (martensite). It has also been noticed that excessive training may result in the formation of ά (martensite) due to continuous softening of the alloy during training, thus degrading the shape memory effect. Finally, it has also been noticed that the addition of samarium increases the values of proof stress, critical stress and strain hardening exponent. Although the addition of samarium increases the values of proof stress, critical stress and strain hardening exponent yet it has not an adverse effect on shape memory effect.