حقوق نسواں کا عالمی معاہدہ اور شریعت اسلامیہ: تقابلی مطالعہ CEDAW

Women are confronted with a lot of problems. In different parts of the world, some social and cultural attitudes still discourage the women from getting their established and assigned rights. The factors which are responsible for this phenomenon include societal norms, orthodoxy and some social customs contrary to islamic instructions. For instance, discrimination against women could be in terms of inadequate nutrition, denial or limited access to education, health and property rights, child labor, domestic violence and forceful marriage. So far as the Islamic instructions are concerned, these are derived from Quran and Sunnah and clearly describe women’s rights but, due to some socio-religious customs and undesirable behaviors the societal status and role of women have been badly affected. An international document, the convention on the elimination of all forms of discrimination against women also lists the rights of all girls and women. CEDAW recommends that all discriminations against girls and women must be ended. In this paper, the terms have been analyzed in the context of islamic instructions and teachings, in order to provide academic material for bringing positive change in the society.

Laser Induced Surface Structuring of Metals Correlated With Breakdown Spectroscopy and Field Emission Properties

In this dissertation three important aspects of laser-matter interaction for four selected metals i.e. Zinc (Zn), Copper (Cu), Molybdenum (Mo) and Tungsten (W) are addressed. These aspects include: (1) Understanding of physical processes involved in laser ablation and surface structuring, (2) The role of two important laser induced plasma parameters i.e. electron temperature (Te) and electron number density (ne) for the growth of various surface structures and (3) Applications of these surface structures for enhancing the field emission properties of the selected metals.The laser induced surface structuring is performed by employing both nanosecond (ns) and femtosecond (fs) i.e. Nd:YAG (1064 nm, 10 ns , 10 Hz) and Ti: sapphire (800 nm, 30 fs , 1kHz) laser irradiation. The crater depth is investigated using optical microscope analysis. The surface morphology is explored by Scanning Electron Microscope (SEM) analysis. For the estimation of plasma parameters Laser Induced Breakdown Spectroscopy (LIBS) analysis is employed. The field emission properties are explored by using the self-designed and fabricated set-up in a diode configuration under ultrahigh vacuum condition. The whole dissertation is divided into three parts.Part A deals with the laser induced surface structuring of metals and its correlation with the plasma parameters at various irradiances ranging from 6 GW/cm2 to 50 GW/cm2.The irradiation is carried out for three metals i.e. Zn , Mo and W with low, moderate and high melting points. SEM analysis of laser ablated Zn reveals the formation of microscale ripples, wave-like ridges with cones and cavities. For Mo, large sized grains along with cavities and conical interiors, dense ridges with droplets are seen. For W, the formation of grains with pronounced cracking and large sized cones are observed. The evaluated values of Te explored by LIBS analysis vary from 5973 K to 6240 K for Zn, 6526K to 9305 K for Mo and 7800 K to 16383 K for W. Similarly The values of ne vary from 1.35861×1018 cm-3 to 1.44331×1018 cm-3 for Zn, 0.58,878 × 1018 cm-3 to 0.72,067 × 1018 cm-3for Mo and 0.46,085 × 1018 cm-3 to 0.69,679 × 1018 cm-3 for W.It is found that surface structuring of selected metals strongly depend on the laser irradiance and plasma parameters. Part B and C of the dissertation are independent and deal with ns and fs laser induced surface structuring of selected metals for the enhancement of FE properties. The part B deals with the investigation of FE properties of the ns laser irradiated Cu and W metals at four laser irradiances ranging from 13 GW/cm2to 50 GW/cm2. SEM analysis revealed the formation of ridged protrusions, localized melt pools, cones and pores for Cu, whereas, cones, grains and mounds covered with porous structures are observed for W. The Fowler-Nordheim (FN) plots are found to be linear and confirm the quantum mechanical tunneling phenomena for the structured metals. The values of turn-on field, field enhancement factor and maximum current density rangefrom 5 V/ μm to 8.5 V/ μm , 1380 to 2730and 147 μ A / cm2 to 375 μ A / cm2 for Cu and 5 V/μm to 8.5 V/μm,1300to 3490 and 107 μA/cm2 to 350 μA/cm2 for W respectively. Part C deals with the investigation of FE properties of fs laser irradiated W carried out at six different irradiances ranging from 0.2 × 1014 W/cm2 to 6.9 × 1014 W/cm2. The SEM analysis revealed particulates, grains and nanoscale ripples formation. The values of turn on field, field enhancement factor and maximum current density range from 7 to 15 V/μm, 460 to 6120 and 134 μA/cm2 to 341 μA/cm2 respectively. The obtained FE parameters are well correlated with the surface morphology and comparable to the previously reported values.Overall dissertation presents the idea that both laser irradiance and plasma parameters can provide a better control over micro/nano structuring of metals which make them potential candidate for the enhancement in the FE properties as well as other applications.